WiFi Configuration Guide For FingerTec TA100C

Friday, February 22, 2019 TimeTec 9 Comments




Introduction:
WiFi is considered as one of the most required technological aspects for a modern lifestyle. As such, there are many WiFi compatible devices offered in the market today that can connect to the Internet. The WiFi option also allows for an easier biometric device installation without the need for wiring as well as facilitates a faster and stable real-time transfer of attendance data. That said, FingerTec likewise provides a variety of biometric devices which can support WiFi connection, i.e. TA100C, TA200 Plus, Q2i, TA700W and all Face ID Models.

Hence in this technical tip, we will be providing a step by step guide on how to connect FingerTec TA100C device to a WiFi Hotspot.

Process: 
1. In FingerTec TA100C device, proceed to Menu > Comm > Wireless Network. *Note that Wireless Network in the Comm section will only be displayed after the WiFi Settings has been enabled for the device.

2. Once done, the list of available WiFi Hotspot in range will be displayed in the Wireless Network section.
 

3. Choose the Network that you want to connect to and proceed to Insert the Network Password. Once done, select Connect to WiFi. Please note to use the Right Key button to switch between Alphabetic Characters and Alphanumeric Characters.

4. Moving on, the device will then proceed to connect into the network. If the error “Searching for IP Address” still persists after two minutes; please check your WiFi password again or your Wi-fi router setting.

5. The connection Status will display the text ‘Connected’ after the device has successfully connect to the WiFi router.

6. You can also press the M/Ok button to view the WiFi Connection details as shown in the screenshot below. Here, the WiFi Signal Strength and Device IP address will be displayed as well.
 

7. If you have an IP address that you wish to insert Manually at the device, you can do so by turning “Off” the DHCP feature at Menu > Comm > Wireless Network > Advanced. Next, proceed to key in your Network IP address. Note that by default the DHCP setting is turned On for all FingerTec devices.

Note: If some of the screenshots or steps viewed here are different from the ones in the current system, this is due to our continuous effort to improve our system from time to time. Please notify us at info@timeteccloud.com, we will update it as soon as possible.

9 comments:

  1. hello i have TA100C, but i am enable to configure and set up it.Help me

    ReplyDelete
  2. Hello Sir,

    Regarding to your query before you can configure and enable your device with Wifi connection, please make sure you already order or buy the TA100C device with additional Wifi module. For further checking whether your device available with this features or not, please share with us your device serial number.

    However if you already order the TA100C device with Wifi module, but still facing a problem to enable the setting, kindly share with us your device main menu picture together with Wireless Network setting, then email to us at support@fingertec.com to get further assistance.

    Best Regards.

    ReplyDelete
  3. Hi, Both devices (Fingertec and my laptop) on the same ip address, but for some reason, when I try to ping it, it comes up as request timed out. but all the other ip addresses (like my phone and printer) are coming back fine. It's only fingertec that is not responding.

    ReplyDelete
  4. This is a good post. This post gives truly quality information. I’m definitely going to look into it. Really very useful tips are provided here. Thank you so much. Keep up the good works 192.168 1.1

    ReplyDelete
  5. Refrain from committing any typing mistakes while you are inserting the login IP address 192.168.1.1 into the location bar or the address field of the browser.

    ReplyDelete
  6. Another common yet major reason why you are struggling with Netgear router not connecting to internet issue after performing the reset process is that the Ethernet cable you have put in use is worn-out or damaged.

    ReplyDelete
  7. A reset button is given at the back of the router, just long press it and the reset process will start. It will wipe up all the data and settings in the Netgear N600 WiFi router.

    ReplyDelete
  8. You must connect your WiFi router to modem carefully and correctly. Just follow some simple steps to clink your networking devices.

    ReplyDelete
  9. The Netgear router keeps going offline issue means unexpected delays in online tasks. Therefore, you should hurry to get rid of the issue.

    ReplyDelete

Have any questions or inquiries about FingerTec? Drop your input here.